The short version of accuracy fits in a sentence. The long version — which is the one that helps — is below.
Reviewed 2026-02-03. Anything still debated is marked as such rather than presented as settled.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
| Property | Value | Notes |
|---|---|---|
| Retention time RSD | ≤1% for five replicate injections | Typical criterion; method-specific limits apply. |
| Resolution | ≥1.5 between critical pair | Baseline separation is generally desired. |
| Tailing factor | ≤2.0 | Measures peak symmetry. |
| Theoretical plates | ≥2000 per column | Method-dependent; higher values indicate greater efficiency. |
| Peak area RSD | ≤2% for replicate injections | Reflects autosampler and detector precision. |
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
2 December – Neville Callaghan, 77, racehorse trainer. 5 December – Rosemary Smith, 86, rally driver. 7 December – Thomas Kilroy, 89, playwright and novelist. 10 December Jonathan Irwin, 82, blood stock agent, auctioneer, stud owner, publisher and founder of the Jack and Jill Foundation. Syd Millar, 89, rugby union player (Ballymena, national team), coach (British & Irish Lions) and International Rugby Board chairman (2003–2007). Born in Northern Ireland. Bill McCarthy, 87, hurler (St Brendan's, Ardfert, Kerry junior team, Munster). 11 December – Frank Twomey, 68, children's television entertainer and comedian (Bosco, Bull Island). 16 December – Joseph Finnegan, 81, judge. 17 December – Maureen Flavin Sweeney, 100, postmistress and formerly a weather forecaster notable for advising on the D-Day landings. 20 December – Johnny Flaherty, 76, hurler (Kinnitty, Offaly senior team, Leinster). 21 December – Martin Feeley, 73, Olympic rower (1976) and surgeon. 27 December – Éamonn Draper, 83, actor and director. 28 December – Patrick Walsh, 92, Roman Catholic prelate, bishop of Down and Connor (1991–2008). 30 December – Paddy Murphy, 89, Gaelic footballer (Dromtarriffe, Duhallow, Cork senior team.
Casuarinas are flowering plants with fruit and leaves resembling the leaves and cones of the gymnosperm pines Some dicots (Anemone) and monocots (Trillium) in inhospitable environments are able to form underground organs such as corms, bulbs and rhizomes for reserving of nutrition and water until the conditions become better. Carnivorous plants: nitrogen-deficient plants have in at least seven distinct times become carnivorous, like: flypaper traps such as sundews and butterworts, spring traps-Venus fly trap, and pitcher traps in order to capture and digest insects to obtain scarce nitrogen. Pitcher plants: the pitcher trap evolved independently in three eudicot lineages and one monocot lineage. Similar-looking rosette succulents have arisen separately among plants in the families Asphodelaceae (formerly Liliaceae) and Crassulaceae. The orchids, the birthwort family and Stylidiaceae have evolved independently the specific organ known as gynostemium, more popular as column. The Euphorbia of deserts in Africa and southern Asia, and the Cactaceae of the New World deserts have similar modifications (see picture below for one of many possible examples). Sunflower: some types of sunflower and Pericallis are due to convergent evolution. Crassulacean acid metabolism (CAM), a carbon fixation pathway that evolved in multiple plants as an adaptation to arid conditions. C4 photosynthesis is estimated to have evolved over 60 times within plants, via multiple different sequences of evolutionary events.
The three substrates of this enzyme are an opine such as (2S)-2-[(R)-1-carboxyethylamino]pentanoic acid (1), oxidised nicotinamide adenine dinucleotide (NAD+), and water. When acting in the forward direction, the products in this example are L-norvaline, reduced NADH, pyruvic acid and a proton. The enzyme can also catalyse reactions that make opines by adding a molecule of pyruvic acid or other keto acids to L-amino acids. This includes making derivatives of L-methionine, L-isoleucine, L-valine, and L-phenylalanine.
=== Genetics === A malignant peripheral nerve sheath tumor is rare, but is one of the most common non-rhabdomyosarcoma soft tissue sarcomas (NRSTS) in the pediatric population. Neurofibromatosis type 1 (NF-1) is a risk factor for developing MPNSTs. NF-1 is a genetic disorder caused by a mutation on chromosome 17. The lifetime risk of patients with NF-1 developing MPNSTs has been estimated at 8–13%, with a yearly risk of developing MPNSTs of 0.16% compared to 0.001% in the general population.
Sources: en.wikipedia.org
== Nomenclature == In addition to the IUPAC numbering system to differentiate the various carbons in an organic molecule, by sequentially assigning a number to each carbon, including those forming a carboxylic group, the carbons along the side-chain of amino acids can also be labelled with Greek letters, where the α-carbon is the central chiral carbon possessing a carboxyl group, a side chain and, in α-amino acids, an amino group – the carbon in carboxylic groups is not counted. (Consequently, the IUPAC names of many non-proteinogenic α-amino acids start with 2-amino- and end in -ic acid.)
By the 1960s, Bryant Park had entered a state of deterioration, due to a lack of maintenance and its location in a business district with few nighttime activities. In an attempt to deter crime, new lighting was installed in Bryant Park in 1962. Nevertheless, in 1966, parks commissioner Thomas Hoving called a meeting to restore the park, noting its degraded condition. By the 1970s, Bryant Park had been taken over by drug dealers and the homeless, and was considered a no-go area by ordinary citizens and visitors. The condition of the park was so bad that in 1973, parks commissioner Richard M. Clurman threatened to "close Bryant Park and clear it of everybody—until we can get together and make it a place that New Yorkers want it to be." After a man was murdered at the park in 1976, the New York Times noted that gambling and drinking were commonplace at the park. In an opinion piece in the New York Daily News, Jerome Gartner, a coordinator for the Bryant Park Steering Committee, stated that the mugging of a Union Carbide executive in Bryant Park had been quoted as a reason for the company's moving out of New York City. An initial attempt at cleanup was commenced by the Bryant Park Community Fund in the mid-1970s. Free concerts were added in the hope that it would keep out criminals. The initiative was largely unsuccessful, though, and its funding was nearly depleted by 1977. Another initiative, the Bryant Park Steering Committee, was created in 1977 as a partnership between local businesses and the City University of New York.
== Other Branded Generics == Biqi is the brand name for its generic OTC anti-diarrhea pharmaceutical. The Company obtained approval to manufacture and sell Biqi in November 1999. Zaiqi is the brand name for the company's azithromycin granules antibiotics for the treatment of infections. Zaike is the brand name for its cefaclor in dry suspension antibiotics for the treatment of infections. Simcere Kechuanning is the brand name for Simcere Pharmaceutical's OTC herbal medicine used for the treatment of coughs. It comes in oral liquid and tablet formulations. Zaikang is the brand name for its OTC compound zinc gluconate and ibuprofen granules for the treatment of cold symptoms, such as fever, nasal congestion, running nose and sneezing. Faneng is the brand name for the company's alfacalcidol soft capsules for the treatment of osteoporosis.
Sources: en.wikipedia.org
System suitability is typically performed before each batch or according to the validated method and laboratory procedure. Some long runs include periodic checks during analysis. The required frequency depends on regulatory expectations and method performance.
Retention time drift can result from changes in mobile phase composition, column temperature, pump flow, or column age. A gradual shift often points to column degradation. A sudden shift may indicate a leak, mixing error, or incorrect mobile phase.
Retention time alone cannot confirm identity because different compounds may elute at similar times. Coupling HPLC with mass spectrometry or comparing against authenticated standards increases confidence. Confirmation usually requires orthogonal data.
Method validation is the documented process of confirming that an HPLC procedure is suitable for its intended use. It evaluates accuracy, precision, specificity, linearity, range, detection limits, and robustness. Validation criteria depend on the regulatory context and the sample type.