Everything below concerns mobile phase. We keep the language plain, cite what the science says, and separate well-supported claims from open questions.
Updated 2026-01-07. Numbers and descriptions here follow the published literature rather than marketing material.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Measured value compared with true or accepted value |
| Precision type | Repeatability | Same analyst, instrument, and short time interval |
| Linearity range | 50–150% of target concentration | Common for assay methods; method-dependent |
| Limit of quantitation | Signal-to-noise ratio of 10:1 | Lowest concentration with acceptable precision |
| Common synonyms | Method validation, analytical validation | Documented confirmation that a method is suitable |
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
Despite not being encoded by the genetic code as proteinogenic amino acids, some non-standard amino acids are nevertheless found in proteins. These are formed by post-translational modification of the side chains of standard amino acids present in the target protein. These modifications are often essential for the function or regulation of a protein; for example, in γ-carboxyglutamate the carboxylation of glutamate allows for better binding of calcium cations, and in hydroxyproline the hydroxylation of proline is critical for maintaining connective tissues. Another example is the formation of hypusine in the translation initiation factor EIF5A, through modification of a lysine residue. Such modifications can also determine the localization of the protein, for example, the addition of long hydrophobic groups can cause a protein to bind to a phospholipid membrane.
Δh = The head loss due to pipe friction over the given length of pipe (SI units: m); g = The local acceleration due to gravity (m/s2). It is useful to present head loss per length of pipe (dimensionless):
The Church of Saidet et Tallé in Deir el Qamar is one of the most significant historical and religious sites in Mount Lebanon. The original church was destroyed by the Saracens and later rebuilt during the reign of Fakhreddine I Maan (1518-1544). For centuries, this church has been revered by both Druze and Christians in Mount Lebanon, reflecting the close ties between the two communities. According to Pierre-Marie Martin, writing in 1870, the Druze venerated the church even more than the Maronites, often traveling long distances to pray to the Virgin Mary in their own way and "witnessing numerous miracles". Historian Glenn Bowman further highlights that in the early nineteenth century, Druze leaders would seek the Virgin Mary's favor at Saidet et Tallé before going into battle. They would touch the image of the Virgin Mary with their flags and place dust from under the altar in their turbans. The profound veneration of this church by the Druze led local Maronites to dub it the "Church of the Virgin of the Druze". Since the sixteenth century, prominent Druze feudal families have welcomed Protestant missionaries, as well as, Catholic missionaries like Franciscans, Jesuits, Carmelites, and Lazarites to the region, all of whom contributed to the spread of education and literacy. Several feudal Druze families also funded the construction of churches in their strongholds.
Sources: en.wikipedia.org
Some bats prey on other vertebrates, such as fish, frogs, lizards, birds and mammals. The fringe-lipped bat (Trachops cirrhosus), for example, is skilled at catching frogs, locating them by tracking their mating calls. The greater noctule bat (Nyctalus lasiopterus) hunts and catches birds in flight. Some species, like the greater bulldog bat (Noctilio leporinus), hunt fish, flying over the water and grabbing them with their clawed feet. They use echolocation and may be alerted by ripples on the surface or a jumping fish. Some species feed on other bats, including the spectral bat (Vampyrum spectrum) and the ghost bat (Macroderma gigas).
== Contraindications == Hydroxyzine is contraindicated for subcutaneous or intra-articular administration. The administration of hydroxyzine in large amounts by ingestion or intramuscular administration during the onset of pregnancy can cause fetal abnormalities. When administered to pregnant rats, mice, and rabbits, hydroxyzine caused abnormalities such as hypogonadism with doses significantly above that of the human therapeutic range. In humans, a significant dose has not yet been established in studies, and, by default, the US Food and Drug Administration (FDA) has introduced contraindication guidelines regarding hydroxyzine. Use by those at risk for or showing previous signs of hypersensitivity is also contraindicated. Other contraindications include the administration of hydroxyzine alongside depressants and other compounds that affect the central nervous system; if necessary, it should only be administered concomitantly in small doses. If administered in small doses with other substances, as mentioned, then patients should refrain from using dangerous machinery, motor vehicles, or any other practice requiring absolute concentration, under safety laws. Studies have also been conducted which show that long-term prescription of hydroxyzine can lead to tardive dyskinesia after years of use, but effects related to dyskinesia have also anecdotally been reported after periods of 7.5 months, such as continual head rolling, lip licking, and other forms of athetoid movement.
Marmite ( MAR-myte) is a food spread produced in New Zealand by Sanitarium Health and Wellbeing Company and distributed in Australia and the Pacific. It is similar to the British Marmite, but the two products are made by different companies. This is the only product sold as Marmite in Australasia and the Pacific, whereas elsewhere in the world the British version predominates. In the rest of the world it is sold as "NZ-Mite". Marmite has been manufactured in New Zealand since 1919. The product's popularity in England prompted the Sanitarium Health Food Company to obtain sole rights to distribute the product in New Zealand and Australia in 1908. They later began manufacturing Marmite under licence in Christchurch, albeit using a modified version of the original recipe, most notable for its inclusion of sugar and caramel. Common ingredients are also slightly different quantities from the British version; the New Zealand version has high levels of potassium, for example. New Zealand Marmite is described as having a "weaker" or "less tangy" flavour than the British version.
Aglionby, John (8 May 2005). "Singapore finally finds a voice in death row protest". The Observer. London. Retrieved 28 April 2010. "Singapore death penalty shrouded in silence". Reuters. 12 April 2002. Archived from the original on 2 September 2007. Retrieved 30 November 2005. "Singapore clings to death penalty". Agence France-Presse. 21 November 2005.
Sources: en.wikipedia.org
System suitability is a set of checks that confirm the instrument and method perform within limits before sample analysis. It typically includes resolution, tailing factor, retention time, and peak area reproducibility. If a check fails, the run is invalidated until the cause is resolved.
QC samples are usually injected at the beginning, at intervals during the run, and at the end. The exact frequency depends on the method, sample count, and regulatory requirements. Results outside acceptance limits can require rejection of the affected samples and investigation.
Method validation demonstrates that an HPLC procedure produces reliable results for its intended purpose. It provides documented evidence for accuracy, precision, specificity, and other performance characteristics. Regulators and quality systems require validation before a method is used for release or stability testing.
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.